"RIV/61989100:27360/13:86086740!RIV14-MSM-27360___" . "1580-2949" . "8"^^ . "physical and numercal modelling; metering nozzle; machine, subentry shroud; continuous-casting; steel"@en . . . "Physical and numerical modelling of a non-stationary steel flow through a subentry shroud with an inner metering nozzle" . "Gryc, Karel" . "Tkadle\u010Dkov\u00E1, Mark\u00E9ta" . "Materiali in tehnologije" . "Macura, Michal" . . . "SI - Slovinsk\u00E1 republika" . . . "3"^^ . . . . . "[F693C0799AEE]" . "Michalek, Karel" . . "000328433300020" . "Physical and numerical modelling of a non-stationary steel flow through a subentry shroud with an inner metering nozzle"@en . . . "The paper presents new knowledge about physical and numerical modelling of a non-stationary steel flow into a mould through a subentry shroud with an inner, pressed metering nozzle. The physical and numerical modelling was realized under the conditions of the Department of Metallurgy and Foundry at VSB-Technical University of Ostrava. A speci\u00E1l type of the subentry shroud is u\u0161ed during continuous casting of steel in T\u0159ineck\u00E9 \u017Eelez\u00E1rny, a.s. During continuous casting of steel, two unfavourable phenomena were observed. In the first case, it was not possible to increase the casting speed, though the diameter of the metering nozzle was extended. In the second case, a fluctuation of the casting speed among individual casting strands was detected. These two problems did not allow an improvement of the performance of the casting machine. Therefore, the physical and numerical modelling was performed. Attention was focused on the verification of the effect of the inner diameter of the nozzle body and internal diameter of the metering nozzle on the resulting volume flow rates. Four diameters of the metering nozzle - (16; 17; 17.5; 18) mm - were tested. The physical modelling was done on a 1 : 1 model constructed from Plexiglas. The numerical modelling was realized in the ANS YS FLUENT software. On the basis of the results of the modelling study and in cooperation with the VESUVIUS company, a new type of the profile of the subentry shroud with a metering nozzle was designed. The first experimental results in the steel plant led to an increase in the productivity of the continuous-casting machine."@en . . . . "Physical and numerical modelling of a non-stationary steel flow through a subentry shroud with an inner metering nozzle"@en . "5"^^ . . "P(ED0040/01/01)" . "Cupek, Ji\u0159\u00ED" . "The paper presents new knowledge about physical and numerical modelling of a non-stationary steel flow into a mould through a subentry shroud with an inner, pressed metering nozzle. The physical and numerical modelling was realized under the conditions of the Department of Metallurgy and Foundry at VSB-Technical University of Ostrava. A speci\u00E1l type of the subentry shroud is u\u0161ed during continuous casting of steel in T\u0159ineck\u00E9 \u017Eelez\u00E1rny, a.s. During continuous casting of steel, two unfavourable phenomena were observed. In the first case, it was not possible to increase the casting speed, though the diameter of the metering nozzle was extended. In the second case, a fluctuation of the casting speed among individual casting strands was detected. These two problems did not allow an improvement of the performance of the casting machine. Therefore, the physical and numerical modelling was performed. Attention was focused on the verification of the effect of the inner diameter of the nozzle body and internal diameter of the metering nozzle on the resulting volume flow rates. Four diameters of the metering nozzle - (16; 17; 17.5; 18) mm - were tested. The physical modelling was done on a 1 : 1 model constructed from Plexiglas. The numerical modelling was realized in the ANS YS FLUENT software. On the basis of the results of the modelling study and in cooperation with the VESUVIUS company, a new type of the profile of the subentry shroud with a metering nozzle was designed. The first experimental results in the steel plant led to an increase in the productivity of the continuous-casting machine." . . "47" . "6" . . "Physical and numerical modelling of a non-stationary steel flow through a subentry shroud with an inner metering nozzle" . "96172" . "27360" . . . "RIV/61989100:27360/13:86086740" .