. "Injection Moulding, Blowing Agent, Talc, Morphology, Structure"@en . "RIV/46747885:24210/08:#0000523!RIV09-MSM-24210___" . "Injection moulding of plastic parts with talc and with the support of blowing agent."@en . . "Vst\u0159ikov\u00E1n\u00ED d\u00EDl\u016F s mikro\u010D\u00E1sticemi a podporou nadouvadla"@cs . "Knowledge about structure of plastic materials is one of important parameters due to the mechanical properties and impact strength, shrinkage, weight and quality of surface. This paper deals with the monitoring and studying structures for crystalline polymer with mineral fillers \u2013 talc, and for crystalline polymer with additive - blowing agent because a lot of plastic parts are used as parts in the machine design. On the bases of analyse of plastics structure it is possible say, that monitoring of structure is progressive method for control of uniform distribution of mineral fillers in the polymers and efect of blowing agent \u2013 influence on the ending properties and using of plastic parts in the design of machine." . . . "Vst\u0159ikov\u00E1n\u00ED plast\u016F" . "Znalosti struktury plast\u016F jsou jedny z nejd\u016Fle\u017Eit\u011Bj\u0161\u00EDch informac\u00ED, nutn\u00FDch pro mechanick\u00E9 vlastnosti, smr\u0161t\u011Bn\u00ED, hmotnost a kvalitu povrchu. P\u0159\u00EDsp\u011Bvek se zab\u00FDv\u00E1 hodnocen\u00EDm a popisem struktury semikrystalick\u00FDch plast\u016F s miner\u00E1ln\u00EDmi plnivy (talek) a aditivy na b\u00E1zi nadouvadel, nebo\u0165 mnoho plast\u016F se st\u00E1le v\u00EDce pou\u017E\u00EDv\u00E1 p\u0159i konstrukci stroj\u016F. Na z\u00E1klad\u011B anal\u00FDzy struktury je mo\u017En\u00E9 p\u0159edpov\u011Bd\u011Bt rozlo\u017Een\u00ED miner\u00E1ln\u00EDho plniva v matrici, resp. vliv nadouvadel, co\u017E v\u00FDrazn\u011B ovliv\u0148uje kone\u010Dn\u00E9 vlastnosti a pou\u017Eit\u00ED plast\u016F p\u0159i stavb\u011B stroj\u016F a je jednou z progres\u00EDvn\u00EDch metod pro kontrolu vlastnost\u00ED."@cs . . . "Knowledge about structure of plastic materials is one of important parameters due to the mechanical properties and impact strength, shrinkage, weight and quality of surface. This paper deals with the monitoring and studying structures for crystalline polymer with mineral fillers \u2013 talc, and for crystalline polymer with additive - blowing agent because a lot of plastic parts are used as parts in the machine design. On the bases of analyse of plastics structure it is possible say, that monitoring of structure is progressive method for control of uniform distribution of mineral fillers in the polymers and efect of blowing agent \u2013 influence on the ending properties and using of plastic parts in the design of machine."@en . "4"^^ . "Seidl, Martin" . "P\u016Fta, Josef" . . . . . . . . . "3"^^ . "Injection moulding of plastic parts with talc and with the support of blowing agent." . "Z(MSM4674788501)" . "Injection moulding of plastic parts with talc and with the support of blowing agent."@en . "Plast Form Service" . "Vst\u0159ikov\u00E1n\u00ED d\u00EDl\u016F s mikro\u010D\u00E1sticemi a podporou nadouvadla"@cs . . "Praha" . "[D750ABDFE32A]" . . "RIV/46747885:24210/08:#0000523" . "Praha" . "24210" . . "3"^^ . "Injection moulding of plastic parts with talc and with the support of blowing agent." . "2008-01-01+01:00"^^ . "372488" . . "1213-2632" . . . "Lenfeld, Petr" .