Attributes | Values |
---|
rdf:type
| |
Description
| - Únavové chování intermetalické slitiny Fe-28at.%Al s příměsí chrómu a céru válcované za tepla bylo studováno při zvýšených teplotách. Závislost v-deltaK byla naměřena při 20, 300 a 500°C. Slitina vykázala nejvyšší únavovou odolnost při 300°C s výjimkou nízkých hodnot delta K. Lomové plochy porušených těles vykazují různou mikromorfologii lomu. Faktografická analýza určila jako hlavní mikromechanismus únavového lomu za všech studovaných teplot transkrystalické štěpení. Kromě transkrystalického štěpení byly nalezeny také transkrystalické kvazi-štěpné fasety, tvárné a štěpné striace. V oblasti statického dolomu vykazoval materiál s rostoucí teplotou rostoucí schopnost plastické deformace. Došlo ke změně mikromechanismu lomu ze štěpného při 20°C na tvárný důlkový lom při 500°C. (cs)
- The fatigue fracture properties of the hot rolled Fe-28at.%Al intermetallic alloy with the addition of chromium and cerium were studied at elevated temperatures. The fatigue crack growth rate curves were measured at 20, 300 and 500°C. The alloy presents the best resistance against the fatigue crack growth at 300°C, except for the low values of delta K. Fractographic analysis carried out on fracture surfaces of ruptured specimens revealed several failure mechanisms of crack propagation. The main fatigue crack growth mechanism at all studied temperatures is transgranular cleavage. The fatigue fracture surface shows a varied micromorphology. Besides transgranular cleavage, transgranular quasi-cleavage, ductile fatigue and brittle striations were found. In the zone of final fracture, the material showed an increasing capacity of plastic deformation with increasing temperature. Fracture mechanism changed from transgranular cleavage at 20°C to ductile dimpled fracture at 500°C.
- The fatigue fracture properties of the hot rolled Fe-28at.%Al intermetallic alloy with the addition of chromium and cerium were studied at elevated temperatures. The fatigue crack growth rate curves were measured at 20, 300 and 500°C. The alloy presents the best resistance against the fatigue crack growth at 300°C, except for the low values of delta K. Fractographic analysis carried out on fracture surfaces of ruptured specimens revealed several failure mechanisms of crack propagation. The main fatigue crack growth mechanism at all studied temperatures is transgranular cleavage. The fatigue fracture surface shows a varied micromorphology. Besides transgranular cleavage, transgranular quasi-cleavage, ductile fatigue and brittle striations were found. In the zone of final fracture, the material showed an increasing capacity of plastic deformation with increasing temperature. Fracture mechanism changed from transgranular cleavage at 20°C to ductile dimpled fracture at 500°C. (en)
|
Title
| - Šíření únavové trhliny ve slitině na bázi Fe3Al při zkouškách za zvýšených teplot (cs)
- Fatigue Crack Propagation in an Fe3Al Based Alloy Tested at Elevated Temperatures
- Fatigue Crack Propagation in an Fe3Al Based Alloy Tested at Elevated Temperatures (en)
|
skos:prefLabel
| - Šíření únavové trhliny ve slitině na bázi Fe3Al při zkouškách za zvýšených teplot (cs)
- Fatigue Crack Propagation in an Fe3Al Based Alloy Tested at Elevated Temperatures
- Fatigue Crack Propagation in an Fe3Al Based Alloy Tested at Elevated Temperatures (en)
|
skos:notation
| - RIV/68407700:21340/04:04101888!RIV/2005/GA0/213405/N
|
http://linked.open.../vavai/riv/strany
| |
http://linked.open...avai/riv/aktivita
| |
http://linked.open...avai/riv/aktivity
| |
http://linked.open...iv/cisloPeriodika
| |
http://linked.open...vai/riv/dodaniDat
| |
http://linked.open...aciTvurceVysledku
| |
http://linked.open.../riv/druhVysledku
| |
http://linked.open...iv/duvernostUdaju
| |
http://linked.open...titaPredkladatele
| |
http://linked.open...dnocenehoVysledku
| |
http://linked.open...ai/riv/idVysledku
| - RIV/68407700:21340/04:04101888
|
http://linked.open...riv/jazykVysledku
| |
http://linked.open.../riv/klicovaSlova
| - fatigue crack growth; fractography; fracture micromechanisms; iron aluminides (en)
|
http://linked.open.../riv/klicoveSlovo
| |
http://linked.open...odStatuVydavatele
| |
http://linked.open...ontrolniKodProRIV
| |
http://linked.open...i/riv/nazevZdroje
| |
http://linked.open...in/vavai/riv/obor
| |
http://linked.open...ichTvurcuVysledku
| |
http://linked.open...cetTvurcuVysledku
| |
http://linked.open...vavai/riv/projekt
| |
http://linked.open...UplatneniVysledku
| |
http://linked.open...v/svazekPeriodika
| |
http://linked.open...iv/tvurceVysledku
| - Haušild, Petr
- Karlík, Miroslav
- Nedbal, Ivan
- Prahl, Jakub
|
issn
| |
number of pages
| |
http://localhost/t...ganizacniJednotka
| |