Attributes | Values |
---|
rdf:type
| |
rdfs:seeAlso
| |
Description
| - The topic of this work is focused on the surface treatment of steel rods of the material number 15230.6 for increasing the durability during the rotation fatigue tests of nitrided rods. The samples used in the experiment were shaped as standard test bars. Samples were hardened and tempered. One set of samples was utilized to determining the basic Wöhler curves of durability. Another set of samples was intended for the subsequent surface treatment. The test bars surface treatment covered four various procedures of plasma nitriding by four different methods, as well as the gas nitriding, and the last set of samples was carburized. The global Wöhler`s diagram for all samples of rotation fatigue tests is given in Chapter 4 (discussion of the experiment results). The material microhardness HV distribution was measured between 0.05 and 0.55 mm from the surface to the depth of core material with the step of 0.05 mm for the each of four plasma nitriding methods, gas nitriding and carburizing. The microhardness was measured due to verifying the dependence of microhardness and the depth of the layer at the fatigue load limit. The raw material has the value of fatigue limit ± 460 MPa, the plasma nitrided steel fatigue limit is between ± 530 MPa for the nitriding procedure III and ± 600 MPa for the nitriding procedure II, which represents the increasing in the fatigue limit for 15% and 30% respectively. The fatigue limit for the gas nitriding has been reached values ± 540 MPa and ± 585 MPa for carburizing respectively. A similar increase in values can be observed in the values of time fatigue limit, e.g. for N = 105 cycles, the time fatigue limit grows from ± 600 MPa to ± 700 MPa until ± 800 MPa, which represents increasing from 17% to34%. The plotted curves of durability correspond to the courses of microhardness HV 0.05. Based on this comparison, it is evident that for the greater microhardness at the same nitriding layer thickness the fatigue is decreased. This phenomenon c (en)
- Článek se zabývá povrchovou úpravou tyčí z oceli 15 230.6 za účelem zvýšení jejich životnosti při zkoušce únavy za rotace. K experimentu byly použity vzorky tvaru zkušebních tyčí. Vzorky byly kaleny a popuštěny. Byla vyčleněna sada vzorků pro zjištění základní křivky životnosti konstrukcí Wöhlerova diagramu a další sada vzorků pro následnou povrchovou úpravu. Povrchová úprava zkoušených tyčí zahrnovala čtyři postupy plazmové nitridace dle čtyřech receptur, dále nitridaci v plynu a poslední sada vzorků byla cementována. Výsledky únavové zkoušky za rotace byly za všechny sady vzorků pro přehlednou demonstraci výsledků shrnuty do souhrnného Wöhlerova diagramu. U každého ze čtyř postupů plazmové nitridace, nitridace v plynu a cementace byla u vzorků změřena mikrotvrdost HV 0,05 od povrchu do hloubky 0,55 mm s krokem 0,05 mm. Mikrotvrdost byla měřena z důvodu ověření závislosti mikrotvrdosti a hloubce vrstvy na mezi únavy. Na základě naměřených hodnot a zkonstruovaných grafů je patrná závislost hodnoty mikrotvrdosti, tloušťky vrstvy a meze únavy při únavové zkoušce nitridovaných tyčí za rotace.
- Článek se zabývá povrchovou úpravou tyčí z oceli 15 230.6 za účelem zvýšení jejich životnosti při zkoušce únavy za rotace. K experimentu byly použity vzorky tvaru zkušebních tyčí. Vzorky byly kaleny a popuštěny. Byla vyčleněna sada vzorků pro zjištění základní křivky životnosti konstrukcí Wöhlerova diagramu a další sada vzorků pro následnou povrchovou úpravu. Povrchová úprava zkoušených tyčí zahrnovala čtyři postupy plazmové nitridace dle čtyřech receptur, dále nitridaci v plynu a poslední sada vzorků byla cementována. Výsledky únavové zkoušky za rotace byly za všechny sady vzorků pro přehlednou demonstraci výsledků shrnuty do souhrnného Wöhlerova diagramu. U každého ze čtyř postupů plazmové nitridace, nitridace v plynu a cementace byla u vzorků změřena mikrotvrdost HV 0,05 od povrchu do hloubky 0,55 mm s krokem 0,05 mm. Mikrotvrdost byla měřena z důvodu ověření závislosti mikrotvrdosti a hloubce vrstvy na mezi únavy. Na základě naměřených hodnot a zkonstruovaných grafů je patrná závislost hodnoty mikrotvrdosti, tloušťky vrstvy a meze únavy při únavové zkoušce nitridovaných tyčí za rotace. (cs)
|
Title
| - Fatigue tests of nitrided rods (en)
- Únavové zkoušky nitridovaných tyčí
- Únavové zkoušky nitridovaných tyčí (cs)
|
skos:prefLabel
| - Fatigue tests of nitrided rods (en)
- Únavové zkoušky nitridovaných tyčí
- Únavové zkoušky nitridovaných tyčí (cs)
|
skos:notation
| - RIV/60162694:G43__/12:00499714!RIV14-MO0-G43_____
|
http://linked.open...avai/riv/aktivita
| |
http://linked.open...avai/riv/aktivity
| |
http://linked.open...iv/cisloPeriodika
| |
http://linked.open...vai/riv/dodaniDat
| |
http://linked.open...aciTvurceVysledku
| |
http://linked.open.../riv/druhVysledku
| |
http://linked.open...iv/duvernostUdaju
| |
http://linked.open...titaPredkladatele
| |
http://linked.open...dnocenehoVysledku
| |
http://linked.open...ai/riv/idVysledku
| - RIV/60162694:G43__/12:00499714
|
http://linked.open...riv/jazykVysledku
| |
http://linked.open.../riv/klicovaSlova
| - ČSN 415230 steel; Plasma nitriding; fatigue test (en)
|
http://linked.open.../riv/klicoveSlovo
| |
http://linked.open...odStatuVydavatele
| |
http://linked.open...ontrolniKodProRIV
| |
http://linked.open...i/riv/nazevZdroje
| |
http://linked.open...in/vavai/riv/obor
| |
http://linked.open...ichTvurcuVysledku
| |
http://linked.open...cetTvurcuVysledku
| |
http://linked.open...UplatneniVysledku
| |
http://linked.open...v/svazekPeriodika
| |
http://linked.open...iv/tvurceVysledku
| - Hrubý, Vojtěch
- Horák, Vladimír
- Studený, Zbyněk
|
issn
| |
number of pages
| |
http://localhost/t...ganizacniJednotka
| |