Attributes | Values |
---|
rdf:type
| |
Description
| - V současné době je předmětem zkoumání problematika vrubů a jejich vliv na životnost součásti. U mnoha vyrobených součástí nalézáme rozmanité typy vrubů, jako jsou drážky, osazení a díry. Ty bývají místem, kde se koncentruje napětí, tzv. makroskopický koncentrátor napětí. V těchto místech vzniká vyšší riziko destrukce součásti. Mnohokrát konstruktéři předepisují zbytečně vysokou kvalitu povrchu. Je potřeba, aby byla zachována odpovídající kvalita povrchu, a také nezbytné aby součást dosáhla vysoké životnosti. Proto je potřeba této oblasti věnovat pozornost. Článek se zabývá vlivem obráběcí technologie na únosnost vrubové součásti. Jako testovaný materiál byla použita ocel Fe510 dle EN ISO (11523, dle ČSN 42 0002).
- V současné době je předmětem zkoumání problematika vrubů a jejich vliv na životnost součásti. U mnoha vyrobených součástí nalézáme rozmanité typy vrubů, jako jsou drážky, osazení a díry. Ty bývají místem, kde se koncentruje napětí, tzv. makroskopický koncentrátor napětí. V těchto místech vzniká vyšší riziko destrukce součásti. Mnohokrát konstruktéři předepisují zbytečně vysokou kvalitu povrchu. Je potřeba, aby byla zachována odpovídající kvalita povrchu, a také nezbytné aby součást dosáhla vysoké životnosti. Proto je potřeba této oblasti věnovat pozornost. Článek se zabývá vlivem obráběcí technologie na únosnost vrubové součásti. Jako testovaný materiál byla použita ocel Fe510 dle EN ISO (11523, dle ČSN 42 0002). (cs)
- For many manufactured components, we find various types of notches, such as grooves, step and holes. They have a tend to be the place where is concentrated stress, so called the macroscopic stress concentrator. In this area is higher risk of part destruction. In many cases the designer prescribe unnecessarily high surface quality. It is necessary to maintain adequate quality of the surface, and also necessary that the component has attained a high durability. The paper deals with the influence of machining technology carrying capacity of notched components. As the test material was used steel Fe510 according to EN ISO (11523, according to CSN 42 0002). In experiment was machined material Fe510 . On this material was created two notches with same shape and several surrounding areas were machined by different machining methods (see Tab. 1). Roughness was measured on samples and then the samples were tested to cyclic load. In the case where the notch was created by cubic boron nitride has been demonstrated to favorably influence machined using sintered carbide. In addition, you can see the positive influence of microcrystalline corundum. In the case where the notch was created by the blades from high speed steel, the most appropriate technology for machining the surface showed a microcrystalline corundum grinding. Vice versa machining by sintered carbide had the worst impact. If we compare the effect of roughness for durability components, so in notch created by HSS is possible to see positive impact finishing technologies and with lower surrounding surface roughness the sample reach a higher number of cycles. In notch grinding by cubic boron nitride is also possible to see the influence of finishing technology , but the machined surface of the sintered carbide point out the fact that it is necessary to examine this issue more deeply. (en)
|
Title
| - Vliv metod obrábění na únosnost součástí s vrubem
- Vliv metod obrábění na únosnost součástí s vrubem (cs)
- Influence of machining methods on the load capacity notched components (en)
|
skos:prefLabel
| - Vliv metod obrábění na únosnost součástí s vrubem
- Vliv metod obrábění na únosnost součástí s vrubem (cs)
- Influence of machining methods on the load capacity notched components (en)
|
skos:notation
| - RIV/44555601:13420/14:43886259!RIV15-GA0-13420___
|
http://linked.open...avai/riv/aktivita
| |
http://linked.open...avai/riv/aktivity
| |
http://linked.open...iv/cisloPeriodika
| |
http://linked.open...vai/riv/dodaniDat
| |
http://linked.open...aciTvurceVysledku
| |
http://linked.open.../riv/druhVysledku
| |
http://linked.open...iv/duvernostUdaju
| |
http://linked.open...titaPredkladatele
| |
http://linked.open...dnocenehoVysledku
| |
http://linked.open...ai/riv/idVysledku
| - RIV/44555601:13420/14:43886259
|
http://linked.open...riv/jazykVysledku
| |
http://linked.open.../riv/klicovaSlova
| - steel, machining, notch, stress, roughness (en)
|
http://linked.open.../riv/klicoveSlovo
| |
http://linked.open...odStatuVydavatele
| |
http://linked.open...ontrolniKodProRIV
| |
http://linked.open...i/riv/nazevZdroje
| |
http://linked.open...in/vavai/riv/obor
| |
http://linked.open...ichTvurcuVysledku
| |
http://linked.open...cetTvurcuVysledku
| |
http://linked.open...vavai/riv/projekt
| |
http://linked.open...UplatneniVysledku
| |
http://linked.open...v/svazekPeriodika
| |
http://linked.open...iv/tvurceVysledku
| - Holešovský, František
- Lattner, Michal
|
issn
| |
number of pages
| |
http://localhost/t...ganizacniJednotka
| |